raised the door by hand half way, set a garbage can under it to hold while I worked. I screwed it up when I was working on the doggie door in my garage door. It was 2 beeps (or beep buzz beep buzz) which is usually fixed by hitting the profile button as I've had to do twice before and is the answer in the not so useful troubleshooting, but this time it just gave 2 beeps then 2 more. I've had my iDrive for 6+ years now and it stopped today. If it completely stops moving, it's likely that the fuse is blown. The box included two fuses and instruction on how to replace the fuse.ĭid the fuse replacement fix your problem? I also couldnt figure out why my opener quit working but never called the company.I just started to troubleshoot on my own and found the blown fuse. To get the idrive going, I drove to the Radio Shack and bought a pack of four fuses.Ī few days later, I received the fuses from Wayne Dalton (see photo below). It could be purchased at Radio Shack, but they will send me the part for free. The customer service explained to me that the fuse it uses is the 250-volt, 4-amp slow-blow fuse (see photo below). The white panel on the right covers the motor control circuit board (see photo below) and the power circuit.Ī fuse is on the top left hand corner of the circuit board. In the end, they asked me to remove the white panel on the right by unscrewing two Philip screws on the bottom. They led me though a number of sequence to deduce the problem. Calling the customer service resolved the problem quickly. When I pushed the up/down button and the profile button, the garage door opener just chirped and beeped. At one point, it stopped moving altogether. But nevertheless, it had caused my Wayne Dalton idrive for Torsion Spring to fail. Whether it's due to the earth shifting or the old cable drum about to fail is still being debated. Recently, my garage door became off-balance. If our light module is what you need, I'm sure we can come to some arrangement.Wayne Dalton idrive Troubleshooting Tip #1 - Check the Fuse I can only *guess* that the light modules are the same. I can no longer find the original light module (maybe we got rid of it), but ISTR that it had a sensor next to the red button.īTW, ours is the iDrive for Torsion Springs, not the iDrive TorqueMaster. How to tell the difference? The only way I know is that the original one had a hole near the red button on the opener, with the IR diode peeking through that hole. When that all went kaput a couple of years ago W-D sent a complete new unit - the one that has recently quit and cannot be repaired. Have you tried cleaning the contact on the bulb socket? Have you tried retraining the light to the opener?ĭo you know which kind of opener/light module combination you have? Our original one had an infra-red link between the opener and the light module, but this gave a lot of trouble and W-D sent a replacement circuit board and light module which used a radio-frequency link. Our light module seemed to act up a few times over the past few months, but I think it was really just a poor contact with the center contact on the bulb. Those poor German workers! Fancy being paid even less than Chinese workers so that they can keep their jobs! *It really does seem to have been made in Germany, not in China with a German company's name on it. It is very quiet but significantly slower than the iDrive (which was claimed to be much faster than other drives).Ĭons: a) the wall station is not wireless as the iDrive's was, so there is additional wiring to run b) the iDrive had a delayed-closing feature, so that I could press the button and walk out through the still-open door, which would then close behind me c) no staples were included, so I had to make a special trip to the store to buy some to staple the wiring in place. A metal arm connects the door to a carriage containing that motor. The design is very simple: a 24V DC motor with a sprocket travels along a fixed chain inside a metal C-channel. (Amazon also sells them, but there is no free shipping option.) Adding the wireless keypad gets the total price into the free-shipping category. Lowe's and HD both sell them for the same price ($228), but only on line: not in the stores. I read the reviews of the German-made* Sommer Synoris 550 opener and decided to buy one. Our Wayne-Dalton iDrive quit - although the motor was supposed to have a lifetime warranty, they are no longer made and no parts available.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |